You are not logged in. Would you like to login or register?

Parts and Equipment For Sale » Mira Giant counterbore cutter / Like NEW / Cuts Paccar counterbores! » 4/09/2021 9:12 am

Don Weaver
Replies: 2

Go to post

Ahebert wrote:

Don is this tool still for sale will it cut mid stop bores 

It is for sale, but it will not cut mid stop, counterbores.

General Discussion » Guascor gas & diesel block repair » 4/25/2016 4:38 pm

Don Weaver
Replies: 0

Go to post

I am equipped to repair Guascor lower liner o-ring sealing area. I can sleeve that area with the engine in place.
Call me at 717-368-8532
I can also repair that area in many other engines also.

Diesel Engines » Detroit 60 block deck dowel pin puller collets » 11/17/2015 12:21 pm

Don Weaver
Replies: 0

Go to post

I now have Detroit 60 block deck dowel pin puller collets to use with the Kent-Moore/Porta-Tool dowel puller tool.
I have some for sale, if anybody is interest Call Don 717-368-8532ed.

Diesel Engines » Paccar MX-13 liner shims » 10/27/2015 12:58 pm

Don Weaver
Replies: 0

Go to post

=13pxI have Paccar MX-13 liner shims to use when counterbore is too deep for .020" O/S liners.
=13pxCall Don at 717-368-8532

Parts and Equipment For Sale » Paccar MX-13 liner shims » 10/27/2015 12:52 pm

Don Weaver
Replies: 0

Go to post

I have Paccar MX-13 liner shims to use when counterbore is too deep for .020" O/S liners.
Call Don at 717-368-8532

Parts and Equipment For Sale » Mira Giant counterbore cutter / Like NEW / Cuts Paccar counterbores! » 10/27/2015 12:44 pm

Don Weaver
Replies: 2

Go to post

Like New Mira Giant counterbore cutter.
Will cut Cummins KT / Cat D8 / D9 / D398 / D399
Will cut Paccar MX-13! (Compact Graphite Iron)
Asking $5500.00
Call Don 717-368-8532


General Discussion » Cat Injector seat repair » 10/27/2015 12:43 pm

Don Weaver
Replies: 0

Go to post

If your trucking customer is complaining about his Cat engine misfiring under heavy load, he could have warped injector seats, which allows combustion gases to come up past the seat, and deteriorate the bottom fuel O-ring, allowing combustion to get into the fuel passage in the head. This will cause 1 or more of the injectors to misfire.
Cat's only repair for this problem, is to replace the head. Rutts Machine can come to your shop, and remachine the injector seats in the head, while head is still installed. This will save the immense expense of replacing the head, and also allows for minimal downtime. Call Don at 717-368-8532

General Discussion » Cat 6 cylinder block deck repair (In frame) » 10/27/2015 12:31 pm

Don Weaver
Replies: 0

Go to post

   In bulletin SEBF9008, Cat recommends installing Stainless Steel insert
Cat # 179-5410 into the decks of blocks, at the coolant passage, if:
 #1 The pitting is deeper than .005”,
#2 If the pitting has occurred completely around the coolant passage.
This normally requires removing the block from the truck, and disassembling the engine,
and taking it to a machine shop to have it set up in a milling machine to
counterbore the deck of the block, to install these inserts.
Rutts Machine is now equipped to install these
Cat warranty approved inserts,or our own brass or cast iron inserts, (less costly)
 while the engine is still in the truck. (Liners can still be installed)
Call Don at 717-368-8532 or the Shop at 717-367-3011

Board footera

 

Powered by Boardhost. Create a Free Forum


ADDITIONAL INSTRUCTIONS FOR ADDING PHOTOS: To add a photo to your forum post, you must use a link to an image hosted elsewhere. (1) Create a free account on an image hosting website of your choice; we recommend www.imgur.com. (2) Upload your photo and then copy the image link (http://www.example.com) from the image hosting website. (3) Paste the image link into your post using the image tool on the forum. If you have any questions, please email info@aera.org.